Alternative Views:
|
 |
 |
 |
 |
|
 |
|
Product Cost:
| |
79-80 12A [Add $2,399.00]
81-82 12A [Add $2,399.00]
83-85 12A [Add $2,399.00]
84-85 13B [Add $2,499.00]
86-88 non turbo [Add $2,099.00]
89-91 non turbo [Add $2,099.00]
87-88 13B Turbo [Add $2,699.00]
89-91 13B Turbo [Add $2,899.00]
93-95 13B Twin Turbo---Manual transmission [Add $2,899.00]
93-95 13B Twin Turbo----Automatic Transmission [Add $2,899.00]
rx8 04-11 [Add $2,999.00]
|
Engine porting:
| |
None
Street Port (Mild) [Add $150.00]Streetable Intake Porting involves changing the size, shape, position, and surface finish of the ports and port runners. The power increase from porting varies, depending on the other modifications made to the engine, but averages 5 percent. Low-RPM torque is reduced slightly, but idle is still smooth. Intake porting includes two primary and two secondary ports.
Street Port (Wild) [Add $295.00]Streetable Intake Porting involves changing the size, shape, position, and surface finish of the ports and port runners. The power increase from porting varies, depending on the other modifications made to the engine, but averages 10 percent. Low-RPM torque is reduced slightly, but idle is still smooth. Intake porting includes two primary and two secondary ports.
Street Port (Extreme) [Add $425.00]Streetable Intake and Exhaust Porting involves changing the size, shape, position, and surface finish of the ports and port runners. The power increase from porting varies, depending on the other modifications made to the engine, but averages 20 percent. Low-RPM torque is reduced slightly, but idle is still smooth. Intake porting includes two primary and two secondary ports. Exhaust porting includes both exhaust ports (turbo housings only).
|
Engine Core Charge:
| |
79-85 12a or 13b [Add $1,000.00]
86-91 Non Turbo [Add $1,000.00]
86-91 Turbo [Add $1,000.00]
93 and up [Add $1,000.00]
|
Engine Option 1:
| |
None
Brap Brap porting [Add $150.00]Can be added to any porting job, or all by itself, gives the engine that famous sound.
|
Engine Option 2:
| |
None
Polished rotors [Add $50.00]Polishing the rotors helps keep the Carbon from sticking to them, well worth the money
|
Engine Option 3:
| |
None
Corner seal spring upgrade [Add $30.00]The 93 and up engines already use these springs because they are better. If you are ordering a 84-91 engine make sure you select this option
|
Engine Option 4:
| |
None
3mm apex seal upgrade [Add $325.00]We machine both rotors to except the more durable 3mm apex seals, for a more bullet proof engine select this option.
|
Engine Option 5:
| |
None
Powdercoat engine housings [Add $150.00]Powder coated surfaces are more resistant to chipping, scratching, fading, and wearing than other finishes.
|
Engine Option 6:
| |
None
Super Apex Seals [Add $150.00]These seals are more durable, and are designed for the high boost engines.
|
Engine Option 7:
| |
None
Engine Balancing [Add $400.00]If you intend your race engine to run above 8,500 RPM or if the engine is a non-standard assembly, we recommend balancing the rotating assembly. The rotating assembly includes both rotors, main pulley, front and rear counterweights, and the eccentric shaft.
|
Engine Option 8:
| |
None
|
Engine Option 9:
| |
None
|
Engine Option 10:
| |
None
|
Engine Option 11:
| |
None
Mazda Factory Race Rotor Bearings [Add $299.00]Mazda Factory Race (MFR) Rotor Bearings are the best bearings available for engine operation near or above 8,500 RPM. These MFR rotor bearings are manufactured with a deep groove for additional oil storage and offer an additional .0005-inch (approx.) clearance.
|
Engine Option 12:
| |
None
ENG STUD KIT 13B Standard [Add $349.00]Studs are less prone to stretching under high boost applications. More accurate tensioning of engine. Less chance of bolt breakage. High quality 12-point nuts rated at 180,000 PSI tensile strength. Studs manufactured from 4140 chrome moly, heat treated, centreless ground and black oxided. Note the standard factory manual flywheel cannot be used with the Stud Kit.
|
Engine Option 13:
| |
None
ENG STUD KIT 13B Oversized [Add $1,250.00]The High Strength Oversized stud kit eliminates the need for doweling the engine block. All studs act as dowels which massively increases torsionial strength 70%. Rotor housing deflection reduced - increases apex seal life. Less material machined from housings and plates than with doweling, reducing the possibility of cracking. High boost engine expansion reduced. Studs are less prone to stretching under high boost applications. More accurate tensioning of engine. Less chance of bolt breakage. High quality 12-point nuts rated at 180,000 PSI tensile strength. Studs manufactured from 4140 chrome moly, heat treated, centreless ground and black oxided. Note the standard factory manual flywheel cannot be used with the Stud Kit.
|
Engine Option 14:
| |
None
Heavy Duty Water Seal kit [Add $199.00]significant upgrade over the stock OEM coolant seals.
|
|
|
|
 |
|
 |
|
|